Jobs at SPIE Oil & Gas Services

Job description

• SPIE Global Services Energy is looking for E&I Cable Pulling Tech to join its workforce on BONGA Offshore Project in Lagos Nigeria.
• Read and interpret cable schedules, cable routing layouts, termination drawings, wiring diagrams, P&IDs, tray layouts and installation specifications.
• Carry out cable pulling and installation activities for power, control, instrumentation, telecom, fiber-optic, fire alarm, CCTV and other ELV cables as assigned.
• Verify cable routes, tray availability, conduits, ducts and cable trenches before commencing cable-pulling activities.
• Inspect cable drums and verify cable type, size, length, drum number, tag number and destination against approved cable schedules.
• Set up cable drums, rollers, cable socks, pulling ropes, winches and other equipment required for safe and controlled cable installation.
• Perform manual and mechanical cable pulling while maintaining the manufacturer's specified maximum pulling tension, bending radius and installation requirements.
• Ensure cables are properly supported and arranged on cable trays, ladders, conduits, ducts, trenches and underground routes.
• Maintain proper cable separation between power, control, instrumentation, communication and intrinsically safe circuits in accordance with project requirements.
• Ensure cables are not damaged during installation and immediately report any cuts, crushing, excessive bending, sheath damage or other defects.
• Install cables with adequate slack at equipment, junction boxes, panels, marshalling cabinets and termination points to facilitate proper termination.
• Maintain correct cable identification by installing cable tags, markers, ferrules and destination labels at specified locations.
• Dress, arrange and secure installed cables using approved cable ties, cleats, clamps, straps and other cable-management materials.
• Ensure cables are installed neatly and maintain proper routing, spacing, accessibility and workmanship standards.
• Assist electricians and instrument technicians with cable preparation activities, including cable stripping, gland preparation and routing to termination points, within the technician's authorized scope.
• Assist with installation of cables through conduits, cable trays, ladders, underground ducts and cable trenches, including difficult or congested areas.
• Carry out cable pulling in accordance with approved Method Statements, Job Safety Analysis (JSA), Risk Assessments and Permit-to-Work (PTW) requirements.
• Conduct pre-pulling inspections.

QHSE:

• Ensures HSE policy fulfilment during his activities
• Maintains a strong safety culture in line with Company HSE Requirements and Rules
• Ensures compliance with Operating Procedures & Guidelines with the asset to ensure Process Safety, Operational Safety and Plan Integrity
• Management System, including permit-to-work (PTW) procedures, SIMOPS, tool box talks, and  job hazard analyses (JHA). He/she shall immediately address and report any unsafe acts or conditions in the work area.

Profile

• Education: Minimum of an HND or B.Sc. Degree in Electrical Engineering, Electrical/Electronics Technology, or a related technical discipline.
• Equivalent vocational training with relevant field experience will be considered
• Experience: Minimum of 8–10 years of hands-on experience in electrical construction on oil and gas EPC projects, with at least 4–5 years in a supervisory role specifically covering cable tray installation and cable routing.
• Experience on offshore platforms, FPSOs, or Deepwater projects is a strong advantage.

Technical Competencies:

• Cable pulling and installation
• Cable drum handling and management
• Cable tray and ladder installation interface
• Cable routing and dressing
• Power and control cable installation
• Instrumentation and telecom cable installation
• Fiber-optic cable handling awareness
• Cable identification and tagging
• Cable pulling tension and bending-radius control
• Cable cleating and securing
• Reading cable schedules and installation drawings
• Cable testing awareness
• Hazardous-area work practices
• PTW, JSA and HSE compliance
• QA/QC inspection and punch-list clearance.

Certifications (Preferred):

• CompEx or equivalent hazardous area certification 
• Working at Height certificate.

go to method of application »

Job description

• SPIE Global Services Energy is looking for Instrument Tubing Fitter to join its workforce on BONGA Offshore Project in Lagos Nigeria.
• Interpret and work from P&IDs, tubing hook-up drawings, instrument installation drawings, isometric drawings, layouts, and construction specifications.
• Install, route, support, and terminate instrument tubing for pressure, temperature, level, flow, control and other instrumentation systems.
• Carry out installation of stainless steel, copper, carbon steel and other specified tubing materials in accordance with project specifications.
• Fabricate tubing runs by accurately measuring, cutting, bending, forming and assembling tubing to suit approved drawings and site conditions.
• Install and connect tube fittings, compression fittings, ferrule fittings, bulkhead fittings, manifolds, valves, needle valves, check valves and associated accessories.
• Perform tubing installation between instruments, impulse lines, manifolds, process connection points, control valves and junction/interface points.
• Ensure correct tubing routing, including proper slope, accessibility, clearance, supports, separation and protection against mechanical damage.
• Install tubing supports, clamps, brackets and mounting accessories in accordance with approved drawings and engineering requirements.
• Ensure tubing is correctly identified using tag numbers, line numbers, service identification and instrument references.
• Carry out tubing installation for instrument air, process impulse, pneumatic control, hydraulic and other utility services as specified in the project scope.
• Conduct tubing preparation activities including deburring, cleaning, flushing and protection of tube ends before connection.
• Ensure all tubing connections are properly assembled and tightened using the correct tools, torque requirements and manufacturer's installation procedures.
• Carry out leak testing, pressure testing, pneumatic testing and/or hydrostatic testing of tubing systems as required by approved procedures.
• Identify and rectify tubing installation defects such as leaks, incorrect routing, damaged tubing, loose fittings, improper bending or inadequate supports.
• Coordinate with Instrument Fitters, Instrument Technicians, Pipe Fitters, Welders, Electrical Technicians and other construction disciplines to resolve interface issues.
• Verify installed tubing against approved drawings, material specifications, instrument hook-up drawings and project standards before inspection.
• Assist QA/QC.

QHSE:

• Ensures HSE policy fulfilment during his activities
• Maintains a strong safety culture in line with Company HSE Requirements and Rules
• Ensures compliance with Operating Procedures & Guidelines with the asset to ensure Process Safety, Operational Safety and Plan Integrity
• Management System, including permit-to-work (PTW) procedures, SIMOPS, tool box talks, and  job hazard analyses (JHA). He/she shall immediately address and report any unsafe acts or conditions in the work area.

Profile

• Education: Minimum of an HND or B.Sc Degree in Electrical Engineering, Electrical/Electronics Technology, or a related technical discipline
• Equivalent vocational training with relevant field experience will be considered
• Experience: Minimum of 8 - 10 years of hands-on experience in electrical construction on oil and gas EPC projects, with at least 4–5 years in a supervisory role specifically covering cable tray installation and cable routing.
• Experience on offshore platforms, FPSOs, or Deepwater projects is a strong advantage.

Technical Competencies:

•  Instrument tubing installation and fabrication
• Tube bending (Autoclave & Swageloks) and routing
• Compression fitting installation
• Instrument hook-up
• Stainless-steel tubing work
• Pneumatic and hydraulic tubing
• Pressure/leak testing
• Reading P&IDs and instrument hook-up drawings
• Tubing support installation
• Oil & Gas construction practices
• QA/QC inspection requirements
• Permit-to-Work and HSE compliance
• Ability to work at height and in confined/offshore environments where required
• Team coordination and productivity control.

Certifications (Preferred):

• CompEx or equivalent hazardous area certification 
• Working at Height certification
• Confined Space Entry.